2.5' Johnsonite Vinyl Base Molding - 120' Coil Wall Cove Base 2.5 inch tall vinyl base molding is an exciting alternative to traditional wood wall base. How to Install Vinyl Base Cove Molding. Vinyl base cove molding is also known as vinyl base or cove base. Vinyl base is supplied in rolls or in precut lengths, and is.
How to Install Vinyl Base Molding. How to Install Vinyl Base Molding. Vinyl base cove is used in place of baseboard to provide a border between your floor and walls. It is easy to care for and does not need paint. It can be purchased in multiple colors, and precut in 4- foot lengths. Vinyl base cove is used in office buildings, public restrooms, daycare centers, and any place that high amounts of activity or traffic would damage traditional baseboard. Installing vinyl base cove takes no time at all, and you will only need basic household tools.
2. Flip the molding face down on the floor in front of the wall. The ridged backside of the vinyl should be facing up with the bottom curved edge closest to the wall. The top edge of the cove base should fit tight against the wall’s surface and. Vinyl wall base and corners appearance can be enhanced by using Roppe’s.
Things Needed. Tape measure. Pencil. Straight edge. Utility knife. Dropcloth. Caulking gun. 4 tubes of base cove adhesive. Step 1. Measure the square footage of your room. Calculate square footage by measuring the width in feet of one of your longest walls, measuring the width in feet of one of your shortest walls, and multiplying the two numbers together. If your room is perfectly square, you will still multiply the width of two walls.
How to Install Vinyl Base Molding. Vinyl base cove is used in place of baseboard to provide a border between your floor and walls. It is easy to care for and does not.
Cost to Install Base Molding - Notes and General Information. Homewyse cost estimates are 'ballpark' ranges for basic work performed in normal. Vinyl base molding or vinyl cove molding serves two basic purposes. It protects the wall from damage by vacuum cleaners, toys, moving furniture, etc; it also provides. Home Guides » Real Estate Rentals & Leases » Get out of Leases » How to Install Vinyl Base Cove Molding with Adhesive; How to Install Vinyl Base Cove Molding with.
Step 2. Cut off the tip of your tube of adhesive with the utility knife. Stick the thin metal rod attached to your caulking gun into the hole that you cut on the end of the tube of adhesive. A thin aluminum seal covers the adhesive. If your caulking gun does not have a metal rod, use a long, thin nail to break the seal. Insert your tube of adhesive into your caulking gun after you have broken the seal. Step 3. Lay one section of base cove on your dropcloth with the backside facing up.
The backside of your base cove has a rougher appearance than the front. Squeeze a ¼- inch thick line of adhesive across the top, middle, and bottom of the section of base cove. Your top and bottom line of adhesive should be approximately 1/8 inch below the very edge to keep the adhesive from oozing out when you press it to your wall. Step 4. Place your glued section of base cove, with the small rounded edge facing up, on the wall, beginning at one corner of the room. The left or right end, depending on which direction you go, should be tucked into the corner as far as it will go. The bottom edge of your base cove should be touching your floor.
Smooth across this section of base cove with your hands to make sure your lines of adhesive are coming in contact with your wall. Step 5. Apply adhesive to another section of base cove, and line up the appropriate end with the first section of base cove. You should not have space between sections of base cove. Continue the process of applying adhesive to sections of base cove until you reach the next corner. The last section on each wall will most likely have to be cut to fit. Step 6. Measure the distance from the next to the last section of base cove, to the corner of the wall that you are working on.
If you are working from left to right, measure from left to right. Mark the needed length on a section of base cove. Place a straight edge across your marks and use your utility knife to cut your base cove. Your cut end should always be in a corner. Step 7. Repeat each step until you have finished your entire room.
Warnings. If you accidentally get adhesive on your wall or carpet, use a little bit of mineral spirits on a rag to immediately wipe it up. References. Easy. DIY: Installing Vinyl Cove Molding. Related Articles.